A Tanking Situation!

in Hive Motors9 months ago

IMG-20220820-WA0073.jpg

Well Hello There Fellow Technicians And Hivers!


Bruv, Now What Is This?

Well here I thought I was going to be working on transmissions and transmissions only, with the exception of differentials and transfer cases! Basically anything with a gear inside!

Now why do I have a fuel tank in front of me? Dude why?

Well you'll never guess why! A few weeks back we received a police vehicle and it was asked of us to just swap out one injector and be done with it. Hmmm yeah easier said than done, right? It's always like that!

That injector they supplied was buggered, it kept over-fueling the cylinder and then it started running away!

Now we have to do all four of them and clean the fuel tank!

20240219_123531-01.jpeg


Pressure Gets The Job Done!

Pressure always gets the job done! Of-course I used the pressure washer to get rid of all that diesel and dirt.

Why what's the problem? We are going to clean the tank! Laughs! Isn't that what I'm busy with?

I also don't know why I have to be the one doing the cleaning! Oh wait!

20240219_124126-01.jpeg


That's How You Lose A Job!

Now here's the actual reason why I am doing it.

We phoned the place that usually cleans the radiators and well fuel tanks for us, they came and picked it up and five minutes later they were back.

A stupid reason to be honest, they wanted us to remove the fuel pump from the tank. Now if we do that, we might as well clean it ourselves right?
Nothing fancy to it really, the tank is plastic and it's fairly easy to get in everywhere, really it was! I'll show you later!

I was shocked at how clean I was able to get it!

20240219_124136-01.jpeg


Damn The Tank Is Dirty Again!

So this is the thing they were too scared to remove! Okay rather the cap on the tank behind it!

Here is the thing! If it didn't break with me then it should not break with anyone else! Unless you don't check what you do!

Maybe that's just me!

20240219_125249-01.jpeg


I'm Content!

So is Bossman! I think this one can be re-fitted after I re-installed the fuel pump!

Why waste money sending it in for cleaning, they wont do much more than that.

Until the next set of things to do! Stay safe people and be blessed!

20240219_130741-01.jpeg


Take note this is not a how to guide, merely myself talking about the work I do and my thoughts around certain things.

To everyone who made it this far into my post Thank you for the read and the support.

If you found this entertaining or educational please consider a re-blog and up-vote.

Most of all please leave a input in the comments below, whether is good or bad critic I would like to know, whether its your opinion or your way of doing things in a different manner I would like.

Power House Creatives Logos FINAL.png

Connecting the people of #HIVE across South Africa. #hive

Sort:  

Awesome man! This is cool to see, love a good diy and clean up. I try to do minor automotive repairs myself. Currently working on sanding, priming, and spraying the roof of my car as the clear coat has all gone/peeling!

Heck, you say minor work but that sounds a lot like major work to me!

Goodluck with that though! There is hardly anything I hate more than sanding, but that has got to get done as well right!!

!PIZZA
!BEER

This is not an easy job
This happens if you buy faul that is not good it will not allow the car to drive well ans the only option is the wash the tank and remove the old fuel and then replace a new one

Those fuel pump nuts are a nightmare and more if you do not have a tool that facilitates the disassembly and assembly, here in Venezuela is seen in many workshops that remove them turning them with a hammer and a chisel blunt but heat and time always crystallize the material and become brittle, I made with a plate cut into three parts bent in C in the center piece welded a quadrant of 1/2 "and the edges made sliding screws to graduate the diameter of the nut.

PIZZA!

$PIZZA slices delivered:
@technicalside(1/5) tipped @sunsethunter